DAA Mini Multi-Cal XL650 / XL750 Case Feeder

Manufacturer
Double-Alpha Academy

$56.95

in Stock

(51)

Qty:

4 payments of $14.24 with Sezzle

Save for Later

Description:

The Dillon XL650 and the Dillon XL750 are among the very best progressive reloading presses and one of the most popular on the market today.

It’s optional motorized case feeder is an excellent accessory, and highly recommended for those who can afford it. But it does add a substantial cost to the price of the XL650/750.

Many customers choose to start reloading on their XL650/750 without the optional case feeder, and for them the new DAA Mini Case feeder will be a great addition to their press!

In a few short minutes, perhaps while watching your favorite TV show, you can pre-hand-load the 6 tubes of the magazine assembly which will hold a combined 150 pcs of 9mm brass (about 130 of .40, or 120 of 38S).

Using the included DAA Adaptor-Set parts, you simply seat the Magazine atop your XL650/750 using your Casefeed Adaptor, click the first tube into place – and you are ready to go. Each time a tube empties out, click the next one into position and continue reloading.

The DAA Mini Multi-Cal XL650 Case Feeder includes One 6-tube magazine assembly, and one Multi-Cal Adaptor-Set. Since the new design uses your original caliber specific Casefeed Adaptor, you can now use your DAA Mini Multi-Cal XL650/750 Case Feeder to feed brass in any caliber.

It is ONE product, which can be used to handle: 9mm, 38S, 38SPL, 357, 0.40, 10mm, .45, .44, 223 and more.

Additional Magazine Assemblies can be purchased separately should you wish to prepare more than 150 pcs of brass before starting to reload.

Please note:

The Multi-Cal Adaptor-Set is designed to fit snugly onto the Dillon Casefeed Adaptor tubes. If too tight, it may be difficult to remove to clear jams. If too loose, the assembly may wobble or cant a little. There is a slight variance between the various Dillon Casefeed Adaptor tubes, so some light fitting may be needed for a fit perfect to your needs. You can use a file, sandpaper or dremmel to slightly increase the inner dimension of the Support-Ring part.
When filling the tubes, rotate the base of the assembly so that it is positioned between tubes- that way none of the columns line up with the hole in the bottom – and the brass won’t fall out prematurely.

Write Review

Rating: (51)

30 Dec 2024

It works as advertised once you get it installed. I was not aware that this part needed to be custom fitted to your press, when I ordered it. Including installation instructions would have been a nice touch. My rating would have been 4-stars if instructions were provided.

Thomas Simpson

22 May 2024

I love how the case feeder operates, it was easy to install and makes loading on the dillon a breeze. Unlike one of my other progressive presses the only thing I did not like about the dillon is everything is for right hand operation, this eliminates that issue nicely and I will be getting the bullet feeder as well. I would love to see larger caliber case feeder in the future, I load .444 and .308 on the dillon.

Norman Sykora

30 Mar 2024

Works well, I was a little frustrated with having to drum sand to fit the Dillon Case adapter. Takes some getting used to vs. single tube, but works well unless you let a case get in upside down, then a bit messy trying to shut off, pull off the machine and straighten out. Double and triple check case orientation before mounting on the machine!

Bradley Bonnette

20 Mar 2024

I now have 2 of them because I normally load 300 rounds of 9mm per session. This allows me to load two case feeders and I'm set. If I only have 100 rounds to load - which is the same number of rounds as most sleeves of primers - I insert 2 .45 ACP hulls in two of the tubes so I can only put 100 shells in the loader.

These things work great!

Ronald Potier

13 Mar 2024

Works flawlessly. I had to do quite a bit of sanding to get the parts to fit over the Dillon case adapter, but I appreciate that it is such a tight fit now.

Paul Mossman

9 Jan 2024

Purchased mine in April, just got around to using it last month. It is a great accessory and I really like it. Simple to use, fills quick, and lets me have an extended load session without high dollar automated feeders.

Like another recent reviewer I also had to sand parts quite a bit in order for them to fit. My Dillon case feeder tubes for 4 calibers were all at least .020" larger than the ID of the case feed adapter. The angled end that fits over the threaded stud on the press was significantly smaller and required drilling with a letter bit so it would thread on the stud. Once those alterations were made the case feeder works as advertised.

Phil Clements

Items 1 to 6 of 51 total

1 2 3 4 5 6 ...

Also Available In Set(s)